Efectos de holgura de una banda trapezoidal de acoplamiento de un sistema electromecánico sobre magnitudes mecánicas y eléctricas
Resumen
En este artículo se investiga la holgura de una correa trapezoidal de un sistema de acoplamiento sobre las magnitudes eléctricas y mecánicas de un sistema impulsado por un motor de inducción. Las magnitudes mecánicas en cuestión son la posición angular, la velocidad mecánica sobre los ejes de acoplamiento y sobre magnitudes eléctricas que son la corriente del estator estudiada con el análisis espectral. Para las magnitudes mecánicas se lleva a cabo un análisis transitorio al arranque del motor y para las corrientes del estator se realiza un análisis en estado estable. Los resultados experimentales se llevan a cabo utilizando un banco de pruebas instrumentado y la condición de libre y bajo falla es considerada utilizando una polea tensora.
Palabra(s) Clave(s): banco de pruebas, diagnóstico de fallas, posición angular, RPM.
Texto completo:
1020-1035 PDFReferencias
M. Riera-Guasp, J. A. Antonino-Daviu G.-A. Capolino, “Advances in Electrical Machine, Power Electronic and Drive Condition Monitoring and Fault Detection: State of the Art”. Transactions on Industrial Electronics. No. DOI 10.1109/TIE.2014.2375853.
A. Picot, Z. Obeid, J. Regnier, S. Poignant, O. Darnis, P. Maussion, “Statisticbased spectral indicator for bearing fault detection inpermanent-magnet synchronous machines using the stator current”. Mechanical Systems and Signal Processing. Vol. 46. No. 2. June 2014. 424-44 pp.
T. W. Rauber, F. A. Boldt, F. M. Varejao, “Heterogeneous Feature Models and Feature Selection Applied to Bearing Fault Diagnosis”. Transactions on Industrial Electronics. Vol. 62. No. 1. January 2015. 637-646 pp.
V. C. M. N. Leite, J. G. B. da Silva, G. F. C. Veloso, L. E. B. da Silva, G. Lambert-Torres, E. L. Bonaldi, L. E. de Lacerda de Oliveira, “Detection of Localized Bearing Faults in Induction Machines by Spectral Kurtosis and Envelope Analysis of Stator Current”. Transactions on Industrial Electronics. No. DOI 10.1109/TIE.2014.2345330.
A. Soualhi, G. Clerc, H. Razik, F. Rivas, “Long-Term Prediction of Bearing Condition by the Neo-Fuzzy Neuron”. Proc. of SDEMPED. August 2013. 586-591 pp.
W. S. Gongora, H. V. D. Silva, A. Goedtel, W. F. Godoy, S. A. O. da Silva, ”Neural Approach for Bearing Fault Detection in Three Phase Induction Motors”. Proc. of SDEMPED. August 2013. 566-572 pp.
M. Delgado, G. Cirrincione, A. G. Espinosa, J. A. Ortega, H. Henao, “Dedicated Hierarchy of Neural Networks applied to Bearings Degradation Assessment”. Proc. of SDEMPED. August 2013. 544-551 pp.
H. Razik, M. E. K. Oumaamar, G. Clerc, “A Hybrid Kangaroo Algorithm to Assess the State Of Health of Electric Motors”. Proc. Of SDEMPED. August 2013. 43-48 pp.
A. Soualhi, G. Clerc, H. Razik, “Detection and Diagnosis of Faults in Induction Motor Using an Improved Articial Ant Clustering Technique”. Transactions on Industrial Electronics. Vol. 60. No. 9. September 2013. 4053-4062 pp.
M. Y. Kaikaa, M. Hadjami, “Effects of the Simultaneous Presence of Static
Eccentricity and Broken Rotor Bars on the Stator Current of Induction Machine”. Transactions on Industrial Electronics. Vol. 61. No. 5. May 2014. 2452-2463 pp.
K. N. Gyftakis, D. K. Athanasopoulos, J. Kappatou, "Evaluation of Different Broken Bar Fault Diagnostic Means in Double-Cage Induction Motors with FEM”. Proc. of SDEMPED. August 2013. 36-42 pp.
F. R. Blnquez, C. A. Platero, E. Rebollo, F. Blzquez, “Evaluation of the Applicability of FRA for Inter-Turn Fault Detection in Stator Windings”. Proc. of SDEMPED. August 2013. 177-182 pp.
B. Aubert, J. Regnier, S. Caux, D. Alejo, “Kalman Filter Based Indicator for Online Inter-Turn Short-Circuits Detection in Permanent Magnet Synchronous Generators”. Transactions on Industrial Electronics. No. DOI 10.1109/TIE.2014.2348934.
K-H. Kim, “Simple Online Fault Detecting Scheme for Short-Circuited Turn in a PMSM Through Current Harmonic Monitoring”. Transactions on Industrial
Electronics. Vol. 58. No. 6. June 2011. 2565-2568 pp.
S. H. Kia, H. Henao, G. A. Capolino, “Gear Tooth Surface Damage Fault Detection Using Induction Machine Electrical Signature Analysis”. Proc. of SDEMPED. August 2013. 358-364 pp.
D. Zurita, M. Delgado, J.A. Ortega Redondo, L. Romeral, “Intelligent Sensor based on Acoustic Emission Analysis applied to Gear Fault Diagnosis”. Proc. of SDEMPED, August 2013. 169-173 pp.
F. Gu, Y. Shao, N. Hu, B. Fazenda, A. Ball, ”Motor Current Signal Analysis using a Modified Bispectrum for Machine Fault Diagnosis”. Proc. of ICROS-SICE International Joint Conference. August 2009. 4890-4895 pp.
H. Yamashina, S. Okumura and I. Kawai, “Development of a diagnosis technique for failures of V-belts by a cross-spectrum method and a discriminant function approach”. Journal of Intelligent Manufacturing. Vol. 7. July 1995. 85-93 pp.
H. P. Bloch, F.K. Geitner, “Installation and Maintenance of V-belt Drives in Practical Machinery Management for Process Plants”. Vol. 4. 1997. 310-328 pp.
Belt and chain drives in Handbook of Reliability Prediction Procedures for Mechanical Equipment, Technical report, Naval Surface Warfare Center. 1998.
URL de la licencia: https://creativecommons.org/licenses/by/3.0/deed.es
Pistas Educativas está bajo la Licencia Creative Commons Atribución 3.0 No portada. 
TECNOLÓGICO NACIONAL DE MÉXICO / INSTITUTO TECNOLÓGICO DE CELAYA
Antonio García Cubas Pte #600 esq. Av. Tecnológico, Celaya, Gto. México
Tel. 461 61 17575 Ext 5450 y 5146
pistaseducativas@itcelaya.edu.mx